12 demisemiquaver in one beat
This is a complex violin piece, and I need to write 12 demisemiquaver in one beat!
I attach a photo of an Encore part, which allows that. I could not figure it in MuseScore...
Thanks for any help.
| Attachment | Size |
|---|---|
| 20171121_191352.jpg | 2.02 MB |
Comments
See https://musescore.org/en/handbook/tuplets
Make the quarter rest, have it selected.
Go to Notes → Tuplets → Other…
As relation enter 12/4 (put 12 notes of the type where otherwise 4 would fit)
In reply to See https://musescore.org/en… by jeetee
The relation should be 12/8 since there are 8 demisemiquavers in a beat.
In reply to The relation should be 12/8… by mike320
My bad.
My music education always worked with the fraction names (1/4th 1/32th etc) and no demihemisemi-stuff :)
In reply to My bad… by jeetee
I don't know what those words mean, I relied on the picture. I'm American and use the same words as you.
In reply to My bad… by jeetee
Being stuborn, I found a work around: I divided each quarter note (4/4) into two quavers - or eight note - and applied a Ctrl + 6 to the rest. It worked!
Thanks, anyhow.
In reply to Being stuborn, I found a… by Sérgio Neville…
OK... but do you get the number '12' displayed on a single beam, as in your picture?
In reply to OK... but do you get the… by Jm6stringer
No, but I got a two groups of three beams with a '6', which is basically the same.
Anyhow, it sounds as it should...
Tks
In reply to My bad… by jeetee
I am not American and English isn't my mother tongue.
However, I want to explain (As far as I can) :
If you select 4th(Quarter) note: (and went to here: Menu->Notes->Tuplets->Other)
How many tuplets do you want?: 12
Originally, how many of these are, in the selected duration?: 8(x32nd)
Relation: 12 / 8 (means: 12, on 8)
Result: (which durations can enter?): 12x32nd (or combinations of these: 12x32nd(at least 3 or 4x) / 6x16th / 3x8th / 1(½)x4th).
In reply to I am not American and my… by Ziya Mete Demircan
Thank you all, folks, for the help.
However, after solving the problem, I incurred in a new one...
The number of notes (very large as you can see), don't fit on the measure!
If I keep writing, it just vanishes from the page...
A sample is attached. I may try to put the beat in a 2/4 mode, although it may affect the remaining 20 other nstruments...
In reply to Thank you all, folks, for… by Sérgio Neville…
No dont' change time signature pls.
See attachment:
Layout Menu -> Page Settings -> Scaling.
In reply to No dont' change time… by Ziya Mete Demircan
How can I thank you? Great help!
In reply to How can I thank you? Great… by Sérgio Neville…
There's always a "but", Zyia...
It worked, but it changed the entire score for the new scale!
Could it be applied only to a given measure?
I can barely see the notes...
Thanks in advance.
In reply to There's always a "but", Zyia… by Sérgio Neville…
Select the measures;
Open Inspector-> select Notes -> 'Small' ?
In reply to Select the measures;… by Shoichi
It worked. Thanks. Small notes, though...
In reply to There's always a "but", Zyia… by Sérgio Neville…
I think you need to adjust your zoom so a single page can be seen on your screen. The scaling Zyia used is not very small.
In reply to I think you need to adjust… by mike320
I did not get that clear, Mike320. Could you explain further. Tks
In reply to I did not get that clear,… by Sérgio Neville…
The item circled in the picture is the zoom. One of the options in the drop down is page width. On my screen Zyia's method was easy to see and would print nicely on a page. IMHO it's easier to read than making the notes small.
In reply to [inline:Musescore problem… by mike320
OK. Wow!